|
The results below were run under SPARC Solaris 10 using a Seagate ST3146855SS SAS disk.
# /etc/smartmon-ux -J /dev/rdsk/c4t17d0s0
SMARTMon-UX [Release 1.36, Build 8-JUN-2008] - Copyright 2001-2008 SANtools(R), Inc. http://www.SANtools.com
Discovered SEAGATE ST3146855SS S/N "3LN29QG4" on /dev/rdsk/c4t17d0s0 (SMART enabled)(140014 MB)
Read-Write Error Recovery : Page [01h] (Factory, Current, Saved)
Automatic reallocation of write (AWRE) : 1, 1, 1
Automatic reallocation of read (ARRE) : 1, 1, 1
Transfer block (TB) : 0, 0, 0
Read continuous (RC) : 0, 0, 0
Enable early recovery (EER) : 0, 0, 0
Post error (PER) : 1, 1, 1
Disable transfer on error (DTE) : 0, 0, 0
Disable correction (DCR) : 0, 0, 0
Read Retry Count : 11, 11, 11
Correction Span : 255, 255, 255 {R/O}
Head Offset Count : 0, 0, 0 {R/O}
Data Strobe Offset Count : 0, 0, 0 {R/O}
Write Retry Count : 5, 5, 5
Recovery Time Limit : 65535, 65535, 65535
Disconnect-Reconnect : Page [02h] (Factory, Current, Saved)
Buffer full ratio : 0, 0, 0 {R/O}
Buffer empty ratio : 0, 0, 0 {R/O}
Bus inactivity limit : 0, 0, 0 {R/O}
Disconnect time limit : 0, 0, 0 {R/O}
Connect time limit : 0, 0, 0 {R/O}
Maximum burst size : 164, 164, 164
Enable modify data pointers (EMDP) : 0, 0, 0 {R/O}
Fair arbitration : 0, 0, 0 {R/O}
Disconnect immediate (DImm) : 0, 0, 0 {R/O}
Data transfer disconnect control (DTDC) : 0, 0, 0 {R/O}
First burst size : 0, 0, 0 {R/O}
Format Device : Page [03h] (Factory, Current, Saved)
Tracks per zone : 13356, 13356, 13356 {R/O}
Alternate sectors per zone : 0, 0, 0 {R/O}
Alternate tracks per zone : 28, 28, 28 {R/O}
Alternate tracks per lun : 0, 0, 0 {R/O}
Sectors per track : 987, 987, 987 {R/O}
Bytes per sector : 512, 512, 512 {R/O}
Interleave : 1, 1, 1 {R/O}
Track skew factor : 230, 230, 230 {R/O}
Cylinder skew factor : 170, 170, 170 {R/O}
Supports soft sectoring (SSEC) : 0, 0, 0 {R/O}
Supports hard sectoring (SHEC) : 1, 1, 1 {R/O}
Removable Medium (RMB) : 0, 0, 0 {R/O}
Addresses assigned by surface (SURF) : 0, 0, 0 {R/O}
Rigid Disk Device Geometry : Page [04h] (Factory, Current, Saved)
Number of cylinders : 74340, 74340, 74340 {R/O}
Number of heads : 4, 4, 4 {R/O}
Starting write precomp : 0, 0, 0 {R/O}
Starting reduced current : 0, 0, 0 {R/O}
Drive step rate : 0, 0, 0 {R/O}
Landing Zone Cylinder : 0, 0, 0 {R/O}
RPL : 0, 0, 0 {R/O}
Rotational Offset : 0, 0, 0 {R/O}
Medium rotation Rate : 15015, 15015, 15015 {R/O}
Verify Error Recovery : Page [07h] (Factory, Current, Saved)
EER : 0, 0, 0
PER : 1, 1, 1
DTE : 0, 0, 0
DCR : 0, 0, 0
Verify Retry Count : 11, 11, 11
Verify Correction Span (bits) : 255, 255, 255 {R/O}
Verify Recovery Time Limit (ms) : 65535, 65535, 65535
Cache Control : Page [08h] (Factory, Current, Saved)
Initiator control (IC) : 0, 0, 0
Abort Pre-fetch (ABPF) : 0, 0, 0 {R/O}
Caching analysis permitted (CAP) : 0, 0, 0
Discontinuity (DISC) : 1, 1, 1 {R/O}
Size enable (Size) : 0, 0, 0 {R/O}
Write cache enable (WCE) : 0, 1, 1
Multiplication factor (MF) : 0, 0, 0 {R/O}
Read cache disable (RCD) : 0, 0, 0
Demand read retention priority : 0, 0, 0 {R/O}
Demand Write Retention Priority : 0, 0, 0 {R/O}
Disable Pre-fetch Transfer Length : 65535, 65535, 65535 {R/O}
Minimum Pre-fetch : 0, 0, 0
Maximum Pre-fetch : 65535, 65535, 65535
Maximum Pre-fetch Ceiling : 65535, 65535, 65535 {R/O}
Force sequential write (FSW) : 1, 1, 1 {R/O}
LB cache segment size (LBCSS) : 0, 0, 0 {R/O}
Disable read-ahead (DRA) : 0, 0, 0
Vendor-specific bits (VSS) : 0, 0, 0 {R/O}
Number of cache segments : 32, 32, 32 {R/O}
Cache segment size : 0, 0, 0 {R/O}
Non cache segment size : 0, 0, 0 {R/O}
Control Mode : Page [0Ah] (Factory, Current, Saved)
TST : 0, 0, 0 {R/O}
TMF_ONLY : 0, 0, 0 {R/O}
D_SENSE : 0, 0, 0 {R/O}
GLTSD : 0, 0, 0
RLEC : 1, 1, 1
Queue algorithm modifier : 0, 0, 0
QErr : 0, 0, 0 {R/O}
DQue : 0, 0, 0 {R/O}
VS : 0, 0, 0 {R/O}
RAQ : 0, 0, 0 {R/O}
UA_INTLCK_CTRL : 0, 0, 0 {R/O}
SWP : 0, 0, 0 {R/O}
RAERP : 0, 0, 0 {R/O}
UUAERP : 0, 0, 0 {R/O}
EAERP : 0, 0, 0 {R/O}
ATO : 0, 0, 0 {R/O}
TAS : 0, 0, 0 {R/O}
Autoload mode : 0, 0, 0 {R/O}
Ready AER holdoff period : 0, 0, 0 {R/O}
Busy timeout period : 0, 0, 0 {R/O}
Extended self-test completion time : 0, 0, 0
Protocol : Page [18h] (Factory, Current, Saved)
Physical interface : SAS Serial SCSI
Transport layer retries : 0, 0, 0 {R/O}
Protocol Specific Port : Page [19h] (Factory, Current, Saved)
Physical interface : SAS Serial SCSI
Ready LED meaning : 0, 0, 0
I_T nexus loss time (ms) : 2000, 2000, 2000
Initiator response timeout (ms) : 0, 0, 0
PHY identifier #0 : 00h, 00h, 00h
(0)Attached device type : 2, 2, 2 {R/O}
(0)Negotiated link rate : 9, 9, 9 {R/O}
(0)SSP initiator port # : 0, 0, 0 {R/O}
(0)STP initiator port # : 0, 0, 0 {R/O}
(0)SMP initiator port # : 1, 1, 1 {R/O}
(0)SSP target port # : 0, 0, 0 {R/O}
(0)STP target port # : 0, 0, 0 {R/O}
(0)SMP target port # : 1, 1, 1 {R/O}
(0)SAS Address : 5000C5000694BFFDh, 5000C5000694BFFDh, 5000C5000694BFFDh
(0)Attached SAS address : 500A0B82E0894000h, 500A0B82E0894000h, 500A0B82E0894000h
(0)Attached PHY identifier : 0Bh, 0Bh, 0Bh
(0)Prog. min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(0)Hardw min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(0)Prog. max link rate,8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}
(0)Hardw max link rate 8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}
PHY identifier #1 : 01h, 01h, 01h
(1)Attached device type : 2, 2, 2 {R/O}
(1)Negotiated link rate : 9, 9, 9 {R/O}
(1)SSP initiator port # : 0, 0, 0 {R/O}
(1)STP initiator port # : 0, 0, 0 {R/O}
(1)SMP initiator port # : 1, 1, 1 {R/O}
(1)SSP target port # : 0, 0, 0 {R/O}
(1)STP target port # : 0, 0, 0 {R/O}
(1)SMP target port # : 1, 1, 1 {R/O}
(1)SAS Address : 5000C5000694BFFEh, 5000C5000694BFFEh, 5000C5000694BFFEh
(1)Attached SAS address : 500A0B82E0850000h, 500A0B82E0850000h, 500A0B82E0850000h
(1)Attached PHY identifier : 0Bh, 0Bh, 0Bh
(1)Prog. min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(1)Hardw min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(1)Prog. max link rate,8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}
(1)Hardw max link rate 8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}
Power Condition : Page [1Ah] (Factory, Current, Saved)
Idle : 0, 0, 0
Standby : 0, 0, 0
Idle condition timer : 00000005h, 00000005h, 00000005h
Standby condition timer : 00000004h, 00000004h, 00000004h
Informational Exceptions Control : Page [1Ch] (Factory, Current, Saved)
PERF : 1, 0, 0
EBF : 0, 0, 0 {R/O}
EWASC : 1, 1, 1
DExcpt : 0, 0, 0
TEST : 0, 0, 0
EBACKERR : 0, 0, 0 {R/O}
LogErr : 0, 0, 0
MRIE : 4, 6, 6
Interval timer : 00000000h, 00001770h, 00001770h
Report count : 00000001h, 00000000h, 00000000h
Background scanning configuration : Page [1Ch,1] (Factory, Current, Saved)
Bkgrnd suspend on log full (S_L_FULL) : 0, 0, 0 {R/O}
Bkgrnd log only intervention (LOWIR) : 0, 0, 0 {R/O}
Bkgrnd enable medium scan (EN_BMS) : 1, 1, 1 {R/O}
Bkgrnd enable pre-scan (EN_PS) : 0, 0, 0 {R/O}
Bkgrnd medium scan interval (hrs) : 168, 24, 24
Bkgrnd pre-scan time limit (hrs) : 24, 24, 24
Bkgrnd min idle time before scan (ms) : 0, 0, 0 {R/O}
Bkgrnd max time to suspend scan (ms) : 0, 0, 0 {R/O}
Program Ended.
The results below show a Seagate Constellation SAS-2 disk that supports their PowerChoice(TM) technology. Note the differences in the Power Condition and Protocol pages.
root@blue:/merged/smartmon# ./smartmon-ux -J /dev/sg1
SMARTMon-UX [Release 1.52, Build 28-DEC-2010] - Copyright 2001-2010 SANtools(R), Inc. http://www.SANtools.com
Discovered SEAGATE ST9500431SS S/N "9SP154LT" on Device /dev/sg1 (Adapter.Ch/ID.LUN=5.0/0.0) (Not Enabling SMART)(476940 MB)
Read-Write Error Recovery : Page [01h] (Factory, Current, Saved)
Automatic reallocation of write (AWRE) : 1, 1, 1
Automatic reallocation of read (ARRE) : 1, 1, 1
Transfer block (TB) : 0, 0, 0
Read continuous (RC) : 0, 0, 0
Enable early recovery (EER) : 0, 0, 0
Post error (PER) : 0, 0, 0
Disable transfer on error (DTE) : 0, 0, 0
Disable correction (DCR) : 0, 0, 0
Read Retry Count (RRC) : 11, 11, 11
Correction Span (COR_S) : 255, 255, 255 {R/O}
Head Offset Count (HOC) : 0, 0, 0 {R/O}
Data Strobe Offset Count (DSOC) : 0, 0, 0 {R/O}
Write Retry Count (WRC) : 5, 5, 5
Recovery Time Limit (RTL) : 65535, 65535, 65535
Disconnect-Reconnect : Page [02h] (Factory, Current, Saved)
Buffer full ratio (BFR) : 0, 0, 0 {R/O}
Buffer empty ratio (BER) : 0, 0, 0 {R/O}
Bus inactivity limit (BIL) : 0, 0, 0 {R/O}
Disconnect time limit (DTL) : 0, 0, 0 {R/O}
Connect time limit (CTL) : 0, 0, 0 {R/O}
Maximum burst size (MBS) : 314, 314, 314
Enable modify data pointers (EMDP) : 0, 0, 0 {R/O}
Fair arbitration (FA) : 0, 0, 0 {R/O}
Disconnect immediate (DImm) : 0, 0, 0 {R/O}
Data transfer disconnect control (DTDC) : 0, 0, 0 {R/O}
First burst size (FBS) : 0, 0, 0 {R/O}
Format Device : Page [03h] (Factory, Current, Saved)
Tracks per zone (TPZ) : 48080, 48080, 48080 {R/O}
Alternate sectors per zone (ASPZ) : 0, 0, 0 {R/O}
Alternate tracks per zone (ATPZ) : 0, 0, 0 {R/O}
Alt tracks per log unit (ATPLU) : 896, 896, 896 {R/O}
Sectors per track (SPT) : 1220, 1220, 1220 {R/O}
Bytes per sector (DBPPS) : 512, 512, 512 {R/O}
Interleave (INTLV) : 1, 1, 1 {R/O}
Track skew factor (TSF) : 183, 183, 183 {R/O}
Cylinder skew factor (CSF) : 57, 57, 57 {R/O}
Supports soft sectoring (SSEC) : 0, 0, 0 {R/O}
Supports hard sectoring (SHEC) : 1, 1, 1 {R/O}
Removable Medium (RMB) : 0, 0, 0 {R/O}
Addresses assigned by surface (SURF) : 0, 0, 0 {R/O}
Rigid Disk Device Geometry : Page [04h] (Factory, Current, Saved)
Number of cylinders (NOC) : 121820, 121820, 121820 {R/O}
Number of heads (NOH) : 6, 6, 6 {R/O}
Starting write precomp (SCWP) : 0, 0, 0 {R/O}
Starting reduced current (SCRWC) : 0, 0, 0 {R/O}
Drive step rate (DSR) : 0, 0, 0 {R/O}
Landing Zone Cylinder (LZC) : 0, 0, 0 {R/O}
RPL : 0, 0, 0 {R/O}
Rotational Offset (ROTO) : 0, 0, 0 {R/O}
Medium rotation Rate (MRR) : 7200, 7200, 7200 {R/O}
Verify Error Recovery : Page [07h] (Factory, Current, Saved)
Verify enable recovery (VEER) : 0, 0, 0
Verify post error (VPER) : 0, 0, 0
Verify term. on error (VDTE) : 0, 0, 0
Verify disable corr. (VDCR) : 0, 0, 0
Verify retry count (VRC) : 11, 11, 11
Verify Correction Span (VCOR) : 255, 255, 255 {R/O}
Verify Recovery Time Limit (VRT) : 65535, 65535, 65535
Cache Control : Page [08h] (Factory, Current, Saved)
Initiator control (IC) : 0, 0, 0
Abort Pre-fetch (ABPF) : 0, 0, 0 {R/O}
Caching analysis permitted (CAP) : 0, 0, 0
Discontinuity (DISC) : 1, 1, 1 {R/O}
Size enable (Size) : 0, 0, 0 {R/O}
Write cache enable (WCE) : 1, 1, 1
Multiplication factor (MF) : 0, 0, 0 {R/O}
Read cache disable (RCD) : 0, 0, 0
Read retention priority (DRRP) : 0, 0, 0 {R/O}
Write retention Priority (WRP) : 0, 0, 0 {R/O}
Disable pre-fetch xfr len (DPTL) : 65535, 65535, 65535 {R/O}
Minimum pre-fetch (MIPF) : 0, 0, 0
Maximum pre-fetch (MAPF) : 65535, 65535, 65535
Maximum pre-fetch (MAPFC) : 65535, 65535, 65535 {R/O}
Force sequential write (FSW) : 1, 1, 1 {R/O}
LB cache segment size (LBCSS) : 0, 0, 0 {R/O}
Disable read-ahead (DRA) : 0, 0, 0
Disable non vol. cache (DRANV) : 0, 0, 0 {R/O}
Vendor-specific bits (VSS) : 0, 0, 0 {R/O}
Number of cache segments (NCS) : 32, 32, 32 {R/O}
Cache segment size (CSS) : 0, 0, 0 {R/O}
Non cache segment size (NCSS) : 0, 0, 0 {R/O}
Control Mode : Page [0Ah] (Factory, Current, Saved)
Task set type (TST) : 0, 0, 0 {R/O}
Task mgmt only (TMF_ONLY) : 0, 0, 0 {R/O}
Descriptor format (D_SENSE) : 0, 0, 0 {R/O}
Global logging disable (GLTSD) : 1, 1, 1
Report log excp. (RLEC) : 0, 0, 0
Queue alg. modifier (QAM) : 0, 0, 0
Queue error mgmt (QERR) : 0, 0, 0 {R/O}
(DQUE) : 0, 0, 0 {R/O}
(VS) : 0, 0, 0 {R/O}
Report check (RAQ) : 0, 0, 0 {R/O}
Unit attn interlocks (UA_INTLCK) : 0, 0, 0 {R/O}
Software write prot (SWP) : 0, 0, 0 {R/O}
(RAERP) : 0, 0, 0 {R/O}
(UUAERP) : 0, 0, 0 {R/O}
(EAERP) : 0, 0, 0 {R/O}
App tag owner (ATO) : 0, 0, 0 {R/O}
Task aborted status (TAS) : 0, 0, 0 {R/O}
Autoload mode (AUTOL) : 0, 0, 0 {R/O}
Ready AER holdoff period (RAER) : 0, 0, 0 {R/O}
Busy timeout period (BTP) : 0, 0, 0 {R/O}
Extended self-test time (ESTCT) : 6420, 6420, 6420 {R/O}
Protocol : Page [18h] (Factory, Current, Saved)
Physical interface : SAS Serial SCSI
Transport layer retries : 0, 0, 0 {R/O}
Protocol Specific Port : Page [19h] (Factory, Current, Saved)
Physical interface : SAS Serial SCSI
Ready LED meaning : 0, 0, 0
I_T nexus loss time (ms) : 2000, 2000, 2000
Initiator response timeout (ms) : 0, 0, 0
PHY identifier #0 : 00h, 00h, 00h
(0)Attached device type : 1, 1, 1 {R/O}
(0)Negotiated link rate : 10, 10, 10 {R/O}
(0)SSP initiator port # : 1, 1, 1 {R/O}
(0)STP initiator port # : 1, 1, 1 {R/O}
(0)SMP initiator port # : 1, 1, 1 {R/O}
(0)SSP target port # : 0, 0, 0 {R/O}
(0)STP target port # : 0, 0, 0 {R/O}
(0)SMP target port # : 0, 0, 0 {R/O}
(0)SAS Address : 5000C500100E0C25h, 5000C500100E0C25h, 5000C500100E0C25h
(0)Attached SAS address : 5001086000505280h, 5001086000505280h, 5001086000505280h
(0)Attached PHY identifier : 00h, 00h, 00h
(0)Prog. min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8
(0)Hardw min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(0)Prog. max link rate,8=1.5Gbps,9=3Gbps: 10, 10, 10
(0)Hardw max link rate 8=1.5Gbps,9=3Gbps: 10, 10, 10 {R/O}
PHY identifier #1 : 01h, 01h, 01h
(1)Attached device type : 0, 0, 0 {R/O}
(1)Negotiated link rate : 8, 8, 8 {R/O}
(1)SSP initiator port # : 0, 0, 0 {R/O}
(1)STP initiator port # : 0, 0, 0 {R/O}
(1)SMP initiator port # : 0, 0, 0 {R/O}
(1)SSP target port # : 0, 0, 0 {R/O}
(1)STP target port # : 0, 0, 0 {R/O}
(1)SMP target port # : 0, 0, 0 {R/O}
(1)SAS Address : 5000C500100E0C26h, 5000C500100E0C26h, 5000C500100E0C26h
(1)Attached SAS address : 0000000000000000h, 0000000000000000h, 0000000000000000h
(1)Attached PHY identifier : 00h, 00h, 00h
(1)Prog. min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8
(1)Hardw min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}
(1)Prog. max link rate,8=1.5Gbps,9=3Gbps: 10, 10, 10
(1)Hardw max link rate 8=1.5Gbps,9=3Gbps: 10, 10, 10 {R/O}
Max power loss timeout (ms) : 0, 0, 0 {R/O}
Power Condition : Page [1Ah] (Factory, Current, Saved)
Idle (IDLE_A) : 0, 1, 1
Idle (IDLE_B) : 0, 1, 1
Idle (IDLE_C) : 0, 0, 0
Standby (STANDBY_Y) : 0, 0, 0
Standby (STANDBY_Z) : 0, 0, 0
Idle condition timer (IDLE_AT) : 0000000Ah, 0000000Ah, 0000000Ah
Standby condition timer (STANDBY_ZT) : 00008CA0h, 00008CA0h, 00008CA0h
Idle condition timer (IDLE_BT) : 00001770h, 00001770h, 00001770h
Idle condition timer (IDLE_CT) : 00004650h, 00004650h, 00004650h
Standby condition timer (STANDBY_YT) : 00004650h, 00004650h, 00004650h
Informational Exceptions Control : Page [1Ch] (Factory, Current, Saved)
PERF : 0, 0, 0
EBF : 0, 0, 0 {R/O}
EWASC : 1, 1, 1
DExcpt : 0, 0, 0
TEST : 0, 0, 0
EBACKERR : 0, 0, 0 {R/O}
LogErr : 0, 0, 0
MRIE : 0, 6, 6
Interval timer : 00000000h, 00000000h, 00000258h
Report count : 00000001h, 00000000h, 00000000h
Background scanning configuration : Page [1Ch,1] (Factory, Current, Saved)
Bkgrnd suspend on log full (S_L_FULL) : 0, 0, 0 {R/O}
Bkgrnd log only intervention (LOWIR) : 0, 0, 0 {R/O}
Bkgrnd enable medium scan (EN_BMS) : 1, 1, 1 {R/O}
Bkgrnd enable pre-scan (EN_PS) : 1, 1, 1
Bkgrnd medium scan interval (hrs) : 336, 24, 24
Bkgrnd pre-scan time limit (hrs) : 24, 24, 24
Bkgrnd min idle time before scan (ms) : 0, 0, 0 {R/O}
Bkgrnd max time to suspend scan (ms) : 0, 0, 0 {R/O}
Program Ended.
|