Example Mode Page Dump

The results below were run under SPARC Solaris 10 using a Seagate ST3146855SS SAS disk.

smartmon-ux -J /dev/rdsk/c4t17d0s0

Discovered SEAGATE ST3146855SS S/N "3LN29QG4" on /dev/rdsk/c4t17d0s0 (SMART enabled)(140014 MB)

Read-Write Error Recovery : Page [01h] (Factory, Current, Saved)

Automatic reallocation of write (AWRE) : 1, 1, 1

Automatic reallocation of read (ARRE) : 1, 1, 1

Transfer block (TB) : 0, 0, 0

Read continuous (RC) : 0, 0, 0

Enable early recovery (EER) : 0, 0, 0

Post error (PER) : 1, 1, 1

Disable transfer on error (DTE) : 0, 0, 0

Disable correction (DCR) : 0, 0, 0

Read Retry Count : 11, 11, 11

Correction Span : 255, 255, 255 {R/O}

Head Offset Count : 0, 0, 0 {R/O}

Data Strobe Offset Count : 0, 0, 0 {R/O}

Write Retry Count : 5, 5, 5

Recovery Time Limit : 65535, 65535, 65535

Disconnect-Reconnect : Page [02h] (Factory, Current, Saved)

Buffer full ratio : 0, 0, 0 {R/O}

Buffer empty ratio : 0, 0, 0 {R/O}

Bus inactivity limit : 0, 0, 0 {R/O}

Disconnect time limit : 0, 0, 0 {R/O}

Connect time limit : 0, 0, 0 {R/O}

Maximum burst size : 164, 164, 164

Enable modify data pointers (EMDP) : 0, 0, 0 {R/O}

Fair arbitration : 0, 0, 0 {R/O}

Disconnect immediate (DImm) : 0, 0, 0 {R/O}

Data transfer disconnect control (DTDC) : 0, 0, 0 {R/O}

First burst size : 0, 0, 0 {R/O}

Format Device : Page [03h] (Factory, Current, Saved)

Tracks per zone : 13356, 13356, 13356 {R/O}

Alternate sectors per zone : 0, 0, 0 {R/O}

Alternate tracks per zone : 28, 28, 28 {R/O}

Alternate tracks per lun : 0, 0, 0 {R/O}

Sectors per track : 987, 987, 987 {R/O}

Bytes per sector : 512, 512, 512 {R/O}

Interleave : 1, 1, 1 {R/O}

Track skew factor : 230, 230, 230 {R/O}

Cylinder skew factor : 170, 170, 170 {R/O}

Supports soft sectoring (SSEC) : 0, 0, 0 {R/O}

Supports hard sectoring (SHEC) : 1, 1, 1 {R/O}

Removable Medium (RMB) : 0, 0, 0 {R/O}

Addresses assigned by surface (SURF) : 0, 0, 0 {R/O}

Rigid Disk Device Geometry : Page [04h] (Factory, Current, Saved)

Number of cylinders : 74340, 74340, 74340 {R/O}

Number of heads : 4, 4, 4 {R/O}

Starting write precomp : 0, 0, 0 {R/O}

Starting reduced current : 0, 0, 0 {R/O}

Drive step rate : 0, 0, 0 {R/O}

Landing Zone Cylinder : 0, 0, 0 {R/O}

RPL : 0, 0, 0 {R/O}

Rotational Offset : 0, 0, 0 {R/O}

Medium rotation Rate : 15015, 15015, 15015 {R/O}

Verify Error Recovery : Page [07h] (Factory, Current, Saved)

EER : 0, 0, 0

PER : 1, 1, 1

DTE : 0, 0, 0

DCR : 0, 0, 0

Verify Retry Count : 11, 11, 11

Verify Correction Span (bits) : 255, 255, 255 {R/O}

Verify Recovery Time Limit (ms) : 65535, 65535, 65535

Cache Control : Page [08h] (Factory, Current, Saved)

Initiator control (IC) : 0, 0, 0

Abort Pre-fetch (ABPF) : 0, 0, 0 {R/O}

Caching analysis permitted (CAP) : 0, 0, 0

Discontinuity (DISC) : 1, 1, 1 {R/O}

Size enable (Size) : 0, 0, 0 {R/O}

Write cache enable (WCE) : 0, 1, 1

Multiplication factor (MF) : 0, 0, 0 {R/O}

Read cache disable (RCD) : 0, 0, 0

Demand read retention priority : 0, 0, 0 {R/O}

Demand Write Retention Priority : 0, 0, 0 {R/O}

Disable Pre-fetch Transfer Length : 65535, 65535, 65535 {R/O}

Minimum Pre-fetch : 0, 0, 0

Maximum Pre-fetch : 65535, 65535, 65535

Maximum Pre-fetch Ceiling : 65535, 65535, 65535 {R/O}

Force sequential write (FSW) : 1, 1, 1 {R/O}

LB cache segment size (LBCSS) : 0, 0, 0 {R/O}

Disable read-ahead (DRA) : 0, 0, 0

Vendor-specific bits (VSS) : 0, 0, 0 {R/O}

Number of cache segments : 32, 32, 32 {R/O}

Cache segment size : 0, 0, 0 {R/O}

Non cache segment size : 0, 0, 0 {R/O}

Control Mode : Page [0Ah] (Factory, Current, Saved)

TST : 0, 0, 0 {R/O}

TMF_ONLY : 0, 0, 0 {R/O}

D_SENSE : 0, 0, 0 {R/O}

GLTSD : 0, 0, 0

RLEC : 1, 1, 1

Queue algorithm modifier : 0, 0, 0

QErr : 0, 0, 0 {R/O}

DQue : 0, 0, 0 {R/O}

VS : 0, 0, 0 {R/O}

RAQ : 0, 0, 0 {R/O}

UA_INTLCK_CTRL : 0, 0, 0 {R/O}

SWP : 0, 0, 0 {R/O}

RAERP : 0, 0, 0 {R/O}

UUAERP : 0, 0, 0 {R/O}

EAERP : 0, 0, 0 {R/O}

ATO : 0, 0, 0 {R/O}

TAS : 0, 0, 0 {R/O}

Autoload mode : 0, 0, 0 {R/O}

Ready AER holdoff period : 0, 0, 0 {R/O}

Busy timeout period : 0, 0, 0 {R/O}

Extended self-test completion time : 0, 0, 0

Protocol : Page [18h] (Factory, Current, Saved)

Physical interface : SAS Serial SCSI

Transport layer retries : 0, 0, 0 {R/O}

Protocol Specific Port : Page [19h] (Factory, Current, Saved)

Physical interface : SAS Serial SCSI

Ready LED meaning : 0, 0, 0

I_T nexus loss time (ms) : 2000, 2000, 2000

Initiator response timeout (ms) : 0, 0, 0

PHY identifier #0 : 00h, 00h, 00h

(0)Attached device type : 2, 2, 2 {R/O}

(0)Negotiated link rate : 9, 9, 9 {R/O}

(0)SSP initiator port # : 0, 0, 0 {R/O}

(0)STP initiator port # : 0, 0, 0 {R/O}

(0)SMP initiator port # : 1, 1, 1 {R/O}

(0)SSP target port # : 0, 0, 0 {R/O}

(0)STP target port # : 0, 0, 0 {R/O}

(0)SMP target port # : 1, 1, 1 {R/O}

(0)SAS Address : 5000C5000694BFFDh, 5000C5000694BFFDh, 5000C5000694BFFDh

(0)Attached SAS address : 500A0B82E0894000h, 500A0B82E0894000h, 500A0B82E0894000h

(0)Attached PHY identifier : 0Bh, 0Bh, 0Bh

(0)Prog. min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}

(0)Hardw min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}

(0)Prog. max link rate,8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}

(0)Hardw max link rate 8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}

PHY identifier #1 : 01h, 01h, 01h

(1)Attached device type : 2, 2, 2 {R/O}

(1)Negotiated link rate : 9, 9, 9 {R/O}

(1)SSP initiator port # : 0, 0, 0 {R/O}

(1)STP initiator port # : 0, 0, 0 {R/O}

(1)SMP initiator port # : 1, 1, 1 {R/O}

(1)SSP target port # : 0, 0, 0 {R/O}

(1)STP target port # : 0, 0, 0 {R/O}

(1)SMP target port # : 1, 1, 1 {R/O}

(1)SAS Address : 5000C5000694BFFEh, 5000C5000694BFFEh, 5000C5000694BFFEh

(1)Attached SAS address : 500A0B82E0850000h, 500A0B82E0850000h, 500A0B82E0850000h

(1)Attached PHY identifier : 0Bh, 0Bh, 0Bh

(1)Prog. min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}

(1)Hardw min link rate,8=1.5Gbps,9=3Gbps: 8, 8, 8 {R/O}

(1)Prog. max link rate,8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}

(1)Hardw max link rate 8=1.5Gbps,9=3Gbps: 9, 9, 9 {R/O}

Power Condition : Page [1Ah] (Factory, Current, Saved)

Idle : 0, 0, 0

Standby : 0, 0, 0

Idle condition timer : 00000005h, 00000005h, 00000005h

Standby condition timer : 00000004h, 00000004h, 00000004h

Informational Exceptions Control : Page [1Ch] (Factory, Current, Saved)

PERF : 1, 0, 0

EBF : 0, 0, 0 {R/O}

EWASC : 1, 1, 1

DExcpt : 0, 0, 0

TEST : 0, 0, 0

EBACKERR : 0, 0, 0 {R/O}

LogErr : 0, 0, 0

MRIE : 4, 6, 6

Interval timer : 00000000h, 00001770h, 00001770h

Report count : 00000001h, 00000000h, 00000000h

Background scanning configuration : Page [1Ch,1] (Factory, Current, Saved)

Bkgrnd suspend on log full (S_L_FULL) : 0, 0, 0 {R/O}

Bkgrnd log only intervention (LOWIR) : 0, 0, 0 {R/O}

Bkgrnd enable medium scan (EN_BMS) : 1, 1, 1 {R/O}

Bkgrnd enable pre-scan (EN_PS) : 0, 0, 0 {R/O}

Bkgrnd medium scan interval (hrs) : 168, 24, 24

Bkgrnd pre-scan time limit (hrs) : 24, 24, 24

Bkgrnd min idle time before scan (ms) : 0, 0, 0 {R/O}

Bkgrnd max time to suspend scan (ms) : 0, 0, 0 {R/O}

Program Ended.

Page url: http://www.santools.com/santool/index.html?example_mode_page_dump_sas.htm